Experimental installation for the study of a chisel unit equipped with working bodies with improved geometric characteristics
https://doi.org/10.32786/2071-9485-2024-02-46
Abstract
Research on improving the working bodies of the chisel plow is of great importance in terms of improving the energy efficiency of tillage and improving the environmental performance of agriculture
Introduction. The development of modernized working bodies for the chisel plow is aimed at optimizing the process of chiseling the soil in order to reduce energy consumption. Research shows that the use of such working bodies helps to improve the tillage process, reduce energy consumption and increase the efficiency of the plow.
Object. The object of the study is the working body of a chisel plow, made in the form of a chisel.
Materials and methods. Experimental identification of the properties of the object under study, verification of the validity of accepted hypotheses. Then, on this basis, a comprehensive and in-depth study of the topic of scientific research.
Results and conclusions. An experimental installation has been prepared for production testing of a chisel plow with upgraded working bodies in real conditions, which will allow assessing its operability and economic feasibility. The results of such an inspection can be used to determine the effectiveness of modernized working bodies and make a decision on their introduction into production. The improvement of working bodies for agricultural machinery plays an important role in improving production efficiency. This makes it possible to improve the quality of tillage, reduce fuel consumption and increase the productivity of agricultural machinery. Through the development of innovations and experimental research, we can create more advanced and efficient working bodies, which will ultimately lead to improved working conditions for agricultural workers and increased agricultural productivity.
About the Authors
Yu. A. Shvabauer
Volgograd State Agrarian University
Russian Federation
Russian Federation
Shvabauer Yuriy Aleksandrovich, PhD student of the Department of Power Supply and Energy Systems,
400002, Volgograd, Universitetsky Avenue, 26
S. I. Subbotin
Volgograd State Agrarian University
Russian Federation
Russian Federation
Subbotin Stanislav Igorevich, PhD student of the Department of Power Supply and Energy Systems,
400002, Volgograd, Universitetsky Avenue, 26
D. S. Gapich
Volgograd State Agrarian University
Russian Federation
Russian Federation
Gapich Dmitriy Sergeevich, Doctor of Engineering Sciences, Professor, Head of the Department of Power Supply and Energy Systems,
400002, Volgograd, Universitetsky Avenue, 26
S. D. Fomin
Volgograd State Agrarian University
Russian Federation
Russian Federation
Fomin Sergey Denisovich, Doctor of Engineering Sciences, Professor of the Department of Mechanics, Head of the Center for Scientometric Analysis and International Indexing Systems,
400002, Volgograd, Universitetsky Avenue, 26
References
1. Vetokhin V. I. On the Dynamics of the Shape of the Surface of the Working Organs of Soil Cultivators. Tractors and agricultural machinery. 2010. № 6. Pp. 30-35.
2. Lobachevsky Y. P., Starovoitov S. I. Optimal Profile of the Front Surface of the Chisel Working Body. Agricultural Machinery and Technologies. 2018. V. 12. № 2. Pp. 26-30.
3. Lobachevsky Y. P., Starovoitov S. I. Theoretical and Technological Aspects of the Work of the Loosening Working Organ. Agricultural Machinery and Technologies. 2016. № 5. Pp. 17-23.
4. Borisenko I. B., Dotsenko A. E. Technical and Technological Features of the Combined Working Body. Niva of the Volga region. 2015. № 3 (36). Pp. 89-96.
5. Borisenko I. B., Sokolova M. V. Technological Scheme of the Working Body for Strip Deep Soil Cultivation. Niva of the Volga region. 2014. № 3 (32). Pp. 44-48.
6. Izmailov A., Liskin I., Lobachevskii Ya., Sidorov S., Khoroshenkov V., Mironova A., Luzhnova E. Simulation of soil-cutting blade wear in an artificial abrasive environment based on the similarity theory. Russian Agricultural Sciences. 2017. V. 43. No 1. Pp. 71-74.
7. Lobachevsky Y. P., Starovoitov S. I. Physical Aspects of Loamy Soil. Bryansk: Bryansk State Agrarian University, 2015. 92 p.
8. Lobachevsky Y. P., Starovoitov S. I., Komogortsev V. F. Substantiation of Parameters of Soil-Cutting Working Bodies for Operating Conditions on Loamy Soils. Moscow: Federal Scientific Agroengineering Center VIM, 2018. 304 p.
9. Liskin I. V., Lobachevsky Y. P., Mironov D. A., et al. Results of Laboratory Studies of Soil-Cutting Working Bodies. Agricultural Machinery and Technologies. 2018. V. 12. № 4. Pp. 41-47.
10. Lobachevsky Y. P., Lachuga Y. F., Izmailov A. Yu., Shogenov Y. Kh. Scientific and Technical Achievements of Agroengineering Scientific Organizations in the Context of Digital Transformation of Agriculture. Machinery and equipment for the village. 2023. № 3 (309). Pp. 2-12.
11. Babitsky L. F., Sobolevsky I. V., Kuklin V. A. Theoretical prerequisites for bionic justification of the parameters of the working bodies of a stubble cultivator. Agrarian Science of the Euro-North-East. 2019. V. 20. № 2. Pp. 183-191.
12. Dotsenko A. E., Borisenko I. B. Optimization of Structural and Technological Parameters of the MoldboardChisel Working Body. Knowledge. 2015. № 12-1. Pp. 82-88.
13. Borisenko I. B., Sidorov A. N., Meznikova M. V., Sytilin M. N. Technological Process of Basic Processing as a Factor of Resource Saving in the Cultivation of Agricultural Crops. Optimization of Agricultural Land Use and Strengthening of the Export Potential of the Agro-Industrial Complex of the Russian Federation on the Basis of Convergent Technologies: Proceedings of the International Scientific and Practical Conference. Volgograd, 2020. Pp. 112-118.
14. Dzyuba O., Dzyuba A., Polyakov A., Volokh V., Antoshchenkov R., Mykhailov A. Studying the influence of structural-mode parameters on energy efficiency of the plough PLN-3-35. Eastern-European Journal of Enterprise Technologies. 2019. No 3 (1-99). Pp. 55-65.
15. Berdyshev V. E., Tseplyaev A. N., Shaprov M. N., Kharlashin A. V., Sedov A. V., Tseplyaev V. A., Borisenko I. B. Theory and Calculation of Technological Parameters of Agricultural Machines. Volgograd, 2018.
16. Vaskov A. A., Dorokhov A. S., Romanenko V. N. Application of Descriptive Geometry Methods for Graphic Construction of Unfolding Plough Working Surfaces. Bulletin of the Federal State Educational Institution of Higher Professional Education "Moscow State Agroengineering University named after V. P. Goryachkin". 2012. № 1 (52). Pp. 42-44.
17. Vaskov A. A., Dorokhov A. S., Trushina L. N. Graphic construction of working surfaces of plough bodies. Bulletin of the Federal State Educational Institution of Higher Professional Education "Moscow State Agroengineering University named after V. P. Goryachkin". 2012. № 2 (53). Pp. 51-53.
18. Borisenko I. B., Ivantsova E. A., Pleskachev Yu. New technologies of tillage. Proceedings of the Nizhnevolzhsky Agro-University Complex: Science and Higher Professional Education. 2012. № 1 (25). Pp. 14-16.
19. Putrin A. S., Terekhov O. N., Tsikler V. V., Utenkov G. L. Main Characteristics of Soil Particle Motion on the Curved Surface of the Working Body. Izvestiya Orenburg State Agrarian University. 2008. № 1 (17). Pp. 93-98.
20. Babitskii L. F., Sobolevskii I. V., Kuklin V. A. Substantiation of Optimal Operating Modes of Cultivator Tines on Vibration Impact Suspension. Agrarian Science of the Euro-North-East. 2017. № 3 (58). Pp. 69-73.
21. Kostyleva L. V., Gapich D. S., Borisenko I. B. Problematic Issues of Operation of Working Organs of Chisel Guns and Ways to Solve Them. Proceedings of the Nizhnevolzhsky Agro-University Complex: Science and Higher Professional Education. 2015. № 3 (39). Pp. 176-179.
22. Mazitov N. K., Lobachevsky Y. P., Rakhimov R. S., et al. Russian Technology of Soil Cultivation and Sowing Based on Own Competitive Innovative Machines. Achievements of science and technology of the agro-industrial complex. 2014. № 7. Pp. 68-70.
23. Mazitov N. K., Lobachevsky Y. P., Dmitriev S. Yu., et al. Modernized Technology and Technique for Soil Treatment and Sowing in Extreme Conditions. Proceedings of the Russian Academy of Agricultural Sciences. 2014. № 6. Pp. 63-67.
24. Lobachevsky Y. P., Liskin I. V., Sidorov S. A., et al. Development and Technology of Production of Soil Cultivating Working Bodies. Agricultural Machinery and Technologies. 2016. № 4. Pp. 3-8.
25. Izmailov A. Yu., Sidorov S. A., Lobachevsky Y. P., et al. New Materials and Technologies for Carbide Coating for Tillage Machine Parts. Bulletin of Russian Agricultural Science. 2016. № 2. Pp. 66-69.
26. Lobachevsky Y. P., Komogortsev V. F., Starovoitov S. I., Khramovskikh K. A. Analysis of Traction Resistance of Cylindroidal Plough Body Elements. Agricultural Machinery and Technologies. 2016. № 2. Pp. 11-15.
27. Sidorov S. A., Lobachevsky Y. P., Mironov D. A., Zolotarev A. S. Influence of Geometric and Installation Parameters of Plough Working Bodies on Agrotechnical and Power Characteristics. Agricultural Machinery and Technologies. 2020. V. 14. № 2. Pp. 10-16.
28. Izmailov A. Yu., Liskin I. V., Lobachevsky Y. P., et al. Application of similarity theory for modeling the wear of soil-cutting blades in an artificial abrasive environment. Russian Agricultural Science. 2016. № 6. Pp. 48-51.
Review
For citations:
Shvabauer Yu.A., Subbotin S.I., Gapich D.S., Fomin S.D. Experimental installation for the study of a chisel unit equipped with working bodies with improved geometric characteristics. Title in english. 2024;(2 (74)):394-406. (In Russ.) https://doi.org/10.32786/2071-9485-2024-02-46
Views:
26
Email this article 